• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Replacement UPVC Door Handles

Whether you're replacing your handles or need to add extra security, you'll choose the perfect handle for your door. These upvc handles are easy to install and conform to the required 92mm centres of multipoint locks.

The backplate fixing centre and the dimensions of the lever/keyhole are the most important measurements. Compare these measurements to your current marks before making a purchase.

Lever/Pad

Lever pad handles consist of a lever on one side and a paddle-shaped handle on the other. These are designed to work with key wind locks, however they can also be fitted to split spindle multipoint door locks (though you'll need a separate dual spindle lock case).

Once you have selected the correct handle for the doors the available finishes will be shown in the drop-down list. Not all styles of handle are available in every finish though and you should always look over the technical drawings and sizes sections for the specific product that you're looking for to ensure that you get the correct size and fit.

When you are choosing a new set of lever pad door handles made of Upvc it is crucial to make sure that they are in line with the PZ (distance between the spindle of the handle and the centre of the hole for the cylinder) of your existing multipoint door locks, as they need to be in line for the doors to remain locked, whether from the inside or outside. The handles we offer are designed to work with the majority of conventional cylinder locks, however it is advisable to double glazed window handles-check before purchasing.

You will need to remove your handles that you have already installed and then dismantle the lock case if you're upgrading to dual spindle levers for your handle because this will require a split cylinder inline. They can be purchased separately and we offer the complete technical diagram for you to take a look at in the pictures for each product.

It is a good idea to loosen the screws holding your existing door handle and then check the mechanism. If the screws are too tight, you may need to loosen them even more. After that, you can take the spindle from the door handle and replace it with a new upvc window locking handles handle. It is important to ensure that the handle is in the right position before installing it. You can do this by placing your finger between the frame, and the handle, to ensure that it's level.

Lever/Lever

The lever handles for doors are used to operate a multi-point lock using an Euro cylinder. They are found on many old upvc door handles double doors as well as aluminium and wooden doors. They are equipped with a lever on the inside and an outside paddle and are typically available in two different types. Sprung - These include an internal spring cassette within the backplate to help bring the handle lever to a horizontal position. Non-sprung: These do not have a mechanism for bringing the handle lever to a horizontal position.

To repair a door handle lever that is sagging it is necessary to locate the detent access pin or hole. It's usually small, protruding ring, or rectangle, found on the handle base plate. Once you have located the detent access hole or pin, you can remove it using an screwdriver.

When the handle is in a horizontal orientation, you can put the screws back in place and tighten them until the handle stays secure on the base plate. Consider applying a threadlocking solution to the threads of screws to improve grip and prevent them from loosening over time.

There are a variety of reasons why door handles of levers droop. The most common cause is that the fixings have been too tightened and are putting stress on the bearings of the lever, and causing it to pull against the door's face. It could also be that the levers aren't being operated at a straight angle and this is compressing the latch mechanism, preventing it from fully springing back into service.

The most common reason for a sprung lever not working properly is the spring not being in the proper position on the backplate. The easiest way to test this is to move the handle and see whether it returns to its horizontal position.

It is important to repair any loose door handles immediately. This could cause excessive wear on the screws and the handle could fall off the base plate. You should also tighten loose screws frequently to prevent them from becoming looser.

Lever/Snib

These upvc door handles are also referred to as 'Snib' handle sets and have a snib button at the top of the lever that can be pressed down to lock your door if you don't have an dummy lock. They are typically fitted with a Fullex 68PZ (that's 68mm between the spindle's center and lever or the lock centre) door lock. We also have a range of other 68PZ door handles from manufacturers such as Ferco and Fab & Fix.

You can upgrade your home by changing the handles on your doors regardless of whether you're replacing existing handles or installing new ones on doors you have built. There are a variety of door handles made of upvc, including traditional lever on backplate, straight or curving short latches, and knob handles that resemble dummy knobs for multi point locks which are ideal for French doors.

Lever on backplate handles are typically rectangular, but there are also circular or oval shaped versions, which are known as rose door window locking handles. These types of door handles come with an a knob or lever on a backplate, which sits behind the knob or lever and is sometimes called a rosette. However, certain back plates can be removed to allow for concealed fixing.

There is a variety of coloured and chrome finishes available for these handles to match your door and other hardware, such as bolts, knobs and hinges. Some handles are supplied with grub screws that help firmly attach the lever or knob to the spindle. Some handles come with bathroom spindles that can be used to make bathroom locks. They also come with a thumbturn release mechanism and can be used on doors for bathrooms.

Mortise

If your front door's uPVC handle is stuck in the open position, the problem is most likely to be related to the tubular latch. It could be due to a number of things however the most frequent is a lack of lubrication in the latch plate. This can be fixed quite easily by simply opening the door and spraying lubricant over the lock and handle. Alternatively, it could be that the latch plate has been dislodged from the backplate. This can be a bit more problematic and requires a professional to fix it.

A multipoint door handle is the ideal solution to the problem of a door handle that is stuck. The handles are inserted into the faceplate of the door and are operated by an actuated thumb turn knob or key that triggers a cam that locks the deadbolt. The handles are available in different sizes to fit various kinds of uPVC door, and come in various attractive finishes that complement the hardware that is currently in use. The handles can be purchased via the internet or from a local locksmith and are easy to install with clear instructions.

To select a replacement handles for upvc windows handle set, you'll need to be aware of the PZ size of the cylinder. This is the distance in millimetres between the inner edge of the door frame and the centre of the handle hole. You will also need the type of lock on your door, regardless of whether it's a mortise or hook lock. The easiest way to find the right handles once you know the measurements is to use the brand filter on the website. This will narrow down your options and you can then select the correct size from there.

A typical set of handles includes the handle unit and a pair of different length screws, drill guides and installation instructions. Smart versions, like the Igloohome Smart Mortise 2+ include a mortice lock with a keypad. These are more complex models and are ideal for professionals who install them or competent DIYers. Certain handle sets come with various accessories, such as weather strips, which can be used to improve the appearance of the door.